摘要

本文針對照明業界最新提出之數位可定址照明介面協定進行研究，並提出ㄧ套符合此協定的螢光燈照明系統。本文中對數位可定址調光介面協定之歷史淵源及相關內容有詳盡之介紹，並針對預熱型螢光燈可調光電子式安定器之架構深入探討。在實作部份本文以PIC單晶片作為控制單元，並針對協定內容撰寫程式；傳輸模式為半雙工(非同步雙向傳輸)串列式訊號傳輸，並製作雙向轉接電路將雙線訊號和RS-232訊號互相轉換以供電腦接收及發送訊號。最後應用IR及Microchip公司研發之程式作為人機介面，完成符合數位可定址照明介面協定之系統雛形。藉由此雛型之完成，希望能對此協定之後續研究有所幫助。

Abstract

In this thesis, the digital addressable lighting interface protocol was studied and a fluorescent lamp lighting system based on the protocol was proposed. The back ground and the content of the protocol was introduced, and the research of the dimmable electronic ballast with preheat function for fluorescent lamp was done in this thesis. In the realization, a PIC controller was adopted as the control unit, and a code for the protocol was coded; Transmission mode of the system is half duplex mode with serial signal transmission. A DALI – RS 232 conversion bridge circuit was also built for computer communication. The program which has been developed by IR and Microchip was adopted in this system as the user interface. Finally the prototype of a light system based on DALI protocol was implemented in this thesis.

參考文獻

[1] 台電網站：http://www.taipower.com.tw。
[2] A. Trostl, “Let there be light,” Industry Applications Magazine,
IEEE, Vol. 10, Iss. 6, pp.12-18.
[3] International Rectifier, “Technical paper : Analog and digital
fluorescent lighting dimming systems,” 2002.
[4] 張應彬，柯聖浩，“電子安定器之實作技術”，文京圖書有限公司出版。
[5] C. Contenti, “Digitally addressable DALI dimming ballast,” in Conf.
Rec. IEEE APEC’02, 2002, Vol. 2, pp.936-942.
[6] P. F. Hein, “DALI-a digital addressable lighting interface for
lighting electronics,” in Conf. Rec. IEEE IAS’01, 2001, Vol. 2,
pp.901-905.
[7] 歐司朗網站：http://www.osram.com。
[8] 吳財福，余德鴻，“電子式安定器綜論”，全華科技圖書股公司出版，民國86年
6月。
[9] E. E. Hammer and C. Ferrera, “F40 fluorescent lamp consideration for
operation at high frequency,” Journal of the Illuminating
Engineering Society, Vol. 1, 1985, pp.63-74.
[10] Michael Gulko and Beu Yaalov, “Current-sourcing push-pull electronic
ballasts,” in Proc. IEEE APEC’93, 1993, pp. 411-417.
[11] T. H. Yu, L. M. Wu, and T. F. Wu, “Comparisons among self-excited
parallel resonant, series resonant and current-fed push-pull
electronic ballasts,” in Proc. IEEE APEC’94, 1994, pp.421-426.
[12] W. Elendaas, Ed, “Fluorescent lamps and lighting,” New York
Macmillan, 1959.
[13] E. E. Hammer, “Fluorescent lamp starting voltage relationships at
60Hz and high frequency,” Journal of the Illuminating Engineering
Society, pp.36-46, Oct. 1983.
[14] C. S. Moo, W. M. Chen, and H. C. Yen, “A series-resonant electronic
ballast for a rapid-start fluorescent lamps with programmable
starting ,” in Proc. PCC’02 Osaka, pp.95-99, 2002.
[15] IEC60929 : AC-supplied electronic ballast for tubular fluorescent
lamps – performance requirements, 2003.
[16] American Nation Standards for Fluorescent Lamp-Rapid-Start Types-
Dimensional and Electrical Characteristics, American National
Standard Institute Inc..
[17] CNS 13755 : AC supplied electronic ballast for fluorescent lamp, 1998.
[18] IEC 61000-3-2 : Limits for harmonic current emission, 2005.
[19] ST, “AN 966 : Application note for L6561,” 2003.
[20] G. Lutteke and H. C. Raets, “220V main 500kHz class-Econverter using
a bimos,” IEEE Transactions on Power Electronics, Vol. PE-2, No. 3,
1987, pp. 186-193.
[21] A. K. S. Bhat, “Analysis, selection, and design of resonant
inverters for electronic ballasts,” in Conf. Rec. IEEE PESC’94,
1994, pp. 796-804.
[22] M. K. Kazimierczuk and W. Szaraniec, “Electronic ballast for
fluorescent lams,” IEEE Transactions on Power Electronics, Vol. 8,
No. 4, pp.386-395, Oct. 1993.
[23] T. J. Liang, T. S. Liu, and F. J. Chang, “Design and analysis of
dimming electronic ballast” in Proc. IEEE Power Electronics and
Drive System, 1997, Vol. 1, pp. 397-402.
[24] International Rectifier, “IR 21592, 21593 data sheet,” 2003.
[25] Microchip, “Application note : AN 811,” 2002.
[26] 林揚盛，“低光源閃爍螢光燈電子式安定器之設計與研製”，國立成功大學電機
工程學系碩士論文，中華民國93年。