簡易檢索 / 詳目顯示
| 研究生： |
陳冠榮 Chen, Kuan-Jung |
|---|---|
| 論文名稱： |
基於非測地線之纏繞增強高壓氣瓶加工方式開發與分析 Development and Analysis of the Filament Winding Process for High Pressure Vessels Based on Non-Geodesic Winding |
| 指導教授： |
陳介力
Chen, Chieh-Li |
| 學位類別： |
碩士 Master |
| 系所名稱： |
工學院 - 航空太空工程學系 Department of Aeronautics & Astronautics |
| 論文出版年： | 2021 |
| 畢業學年度： | 109 |
| 語文別： | 中文 |
| 論文頁數： | 53 |
| 中文關鍵詞： | 繞線機 、非測地線纏繞 、複材纏繞 、壓力氣瓶 |
| 外文關鍵詞： | Winding Machine, Non-geodesic Winding, Filament Winding, Pressure Vessel |
| 相關次數： | 點閱：103 下載：0 |
| 分享至: |
| 查詢本校圖書館目錄 查詢臺灣博碩士論文知識加值系統 勘誤回報 |
為了使氣瓶纏繞能夠更加快速且降低成本，本文目的在探求纏繞材料少，纏繞厚度低，纏繞效率高的纏繞法，並提出單雙繞線頭的纏繞分析。單繞線頭利用非測地線方程組為基礎以容許滑移係數求得纏繞軌跡，而雙繞線頭的加工方式可增加纏繞軌跡的多樣性。計算單、雙繞線頭兩種方法的披覆複材厚度以及披覆複材耗費總長度，利用不同權重比例，從中找尋較佳的纏繞軌跡。研究以ANSYS軟體模擬複材披覆前後承受12MPa內壓的應力分析比較，觀察披覆後氣瓶應力，從而確認最適合的纏繞軌跡的適用性。
The purpose of this paper is to find the optimization analysis of single and double motors that using to high-pressure-vessel filament winding. The single motor uses the non-geodesic trajectories based on changing slip coefficient, while the double motors can increase the more diversity of the winding trajectories than the single motor. Calculating the thickness and the total cost length of the composite material to find a better winding trajectory. In this paper, we use ANSYS to simulate the static structural analysis with 12MPa internal pressure. Observe the pressure of the vessel after winding and select the most suitable winding trajectory.
Chen, L.H. (2020). Winding Pattern Design and Control of Filament-Machine. MSc Thesis, NCKU.
Lin, Y.M. (2019). Winding Pattern Design of Filament-wound Pressure Vessel. MSc Thesis, NCKU.
Peters, S. T. (2011). Composite filament winding, ASM International.
Quanjin, M., et al. (2018). "Design of portable 3-axis filament winding machine with inexpensive control system." Journal of Mechanical Engineering and Sciences 12(1): 3479-3493.
Sulaiman, S., et al. (2013). Failure analysis of aluminum reinforced composite vessel. Applied Mechanics and Materials, Trans Tech Publ.
Vafaeesefat, A. (2009). "Dome shape optimization of composite pressure vessels based on rational B-spline curve and genetic algorithm." Applied Composite Materials 16(5): 321-330.
Ye, L. and H. R. Daghyani (1996). "Sliding friction and wear of carbon fibre-polyetheretherketon commingled yarn composites against steel." Journal of materials science letters 15(17): 1536-1538.
Zhou, J., et al. (2017). "Dome shape optimization of filament-wound composite pressure vessels based on hyperelliptic functions considering both geodesic and non-geodesic winding patterns." Journal of Composite Materials 51(14): 1961-1969.
王迪 (2017). 不同纏繞工藝下複合材料氣瓶力學性能研究, 大連理工大學.
穆建橋 (2017). 複合材料壓力容器的非測地線纏繞成型及強度分析研究, 武漢理工大學.
校內：2026-08-18公開校外：2026-08-18公開