成功大學博碩士論文系統

簡易檢索 / 詳目顯示

回結果列表

研究生：	鐘豪文 Chung, Hau-Wen
論文名稱：	超寬頻 UWB 無線射頻收發機之寬頻 CMOS RFICs 的設計研究 Design of Broadband CMOS RFICs for UWB Wireless Transceiver
指導教授：	莊惠如 Chuang, Huey-Ru
學位類別：	碩士 Master
系所名稱：	電機資訊學院 - 電腦與通信工程研究所 Institute of Computer & Communication Engineering
論文出版年：	2006
畢業學年度：	94
語文別：	中文
論文頁數：	157
中文關鍵詞：	寬頻、超寬頻、射頻積體電路
外文關鍵詞：	UWB, Broadband, RFIC
相關次數：	點閱：95 下載：6
分享至:	分享至facebook 分享至twitter

查詢本校圖書館目錄查詢臺灣博碩士論文知識加值系統勘誤回報

本論文分為三部份，其中研製之RFIC皆應用於DS-UWB收發機之中，第一部份為研製應用於DS-UWB接收機之3-5-GHz及6-10-GHz寬頻CMOS低雜訊放大器RFIC。第二部份為研製應用於DS-UWB接收機之3-5-GHz及6-10-GHz寬頻CMOS折疊式混波器RFIC。第三部份為研製應用於DS-UWB發射機之3-5-GHz及6-10-GHz寬頻CMOS發射放大器RFIC。第一及第二部份研製之RFIC使用TSMC 0.18-μm 1P6M CMOS製程，第三部份研製之RFIC則使用UMC 0.18-μm 1P6M CMOS 製程。應用於3-5-GHz頻帶之所有RFIC晶片，皆採用打鎊線至FR-4基板上量測；應用於6-10-GHz頻帶之所有RFIC晶片，皆採用on-wafer方式量測。
3-5-GHz寬頻CMOS低雜訊放大器，電路以一共源極電晶體與緩衝器串接而組成，量測結果增益為7.1-9 dB、雜訊指數為4.8-6.1 dB。6-10-GHz寬頻CMOS低雜訊放大器以單級疊接放大器及串接兩級疊接放大器實現，量測結果增益為6-8.4 dB、雜訊指數為4.6-5.1 dB；增益為11-13.8 dB、雜訊指數為5.3-6.2 dB。3-5-GHz寬頻CMOS折疊式混波器，量測結果LO power僅需要-10 dBm、轉換增益為3.8-6.9 dB @ 3 -3.99 GHz & 1.5-4.8 dB @ 4.01-5 GHz、input P1dB為-16.7- -15.1 dBm @ 3-3.99 GHz & -15.2- -12 dBm @ 4.01-5 GHz、LO-RF isolation 33.8 dB。6-10-GHz寬頻CMOS折疊式混波器，量測結果LO power僅需要-3 dBm、轉換增益為-1.8-0.8 dB @ 6 - 7.9 GHz & -3.3- -0.4 dB @ 8.1-10 GHz、input P1dB -6 dBm @ 6-7.9 GHz & -4 dBm @ 8.1-10 GHz、LO-RF isolation 30 dB。2.6-4.6-GHz寬頻CMOS發射放大器，量測結果小訊號增益為9.2-11.9 dB，OP1dB為-3.4-0.3 dBm、PAE為5.8-13.9% @ OP1dB、η為6.1-14.3% @ OP1dB。6-10-GHz寬頻CMOS發射放大器，量測結果小訊號增益為7.6-10.5 dB、OP1dB為2.8- 6.1 dBm、PAE為8.8-17.6% @ OP1dB、η為9.7-21.1% @ OP1dB。

This thesis divides into three parts, all designed RFICs applied to DS-UWB transceiver is included. The first part presents 3-5-GHz and 6-10-GHz broadband CMOS low noise amplifier, the second part is 3-5-GHz and 6-10-GHz broadband CMOS folded-cascode mixer, and the third part is 3-5-GHz and 6-10-GHz broadband CMOS transmitting amplifier. The RFICs included in the first and the second part are designed on TSMC 0.18-μm 1P6M CMOS process, and the third part is on UMC 0.18-μm 1P6M CMOS process. The RFICs applied to 3-5-GHz band is measured on FR-4 PC board, and for 6-10-GHz band is on wafer.
3-5-GHz broadband CMOS low noise amplifier is the combination of a common-source transistor and a buffer. Measured results show a noise figure of 4.8 -6.1 dB, and a gain of 7.1-9 dB. 6-10-GHz broadband CMOS low noise amplifier is implemented by two topologies, respectively: Only one single-stage cascode amplifier, and two single-stage cascode amplifier cascaded. Measured results exhibit a noise figure of 4.6 -5.1 dB, and a gain of 6-8.4 dB; the other is a noise figure of 5.3-6.2 dB, and a gain of 11-13.8 dB. 3-5-GHz broadband CMOS folded-cascode mixer is measured as a conversion gain of -1.5-2.5 dB @ 3 -3.99 GHz & -2.6 -0.9 dB @ 4.01-5 GHz, an input P1dB of -9.5- -10.5 dBm @ 3-3.99 GHz & -8.5- -7.5 dBm @ 4.01-5 GHz, a LO-RF isolation of 33.8 dB, and the required LO power is only -10 dBm. 6-10-GHz broadband CMOS folded-mirror mixer is measured as a conversion gain of -1.8-0.8 dB @ 6 - 7.9 GHz & -3.3- -0.4 dB @ 8.1-10 GHz, and an input P1dB ~ -6 dBm @ 6-7.9 GHz & -4 dBm @ 8.1-10 GHz, a LO-RF isolation of 30 dB, and the required LO power is only -3 dBm. 2.6-4.6-GHz broadband CMOS TA is measured as a small signal gain of 9.2-11.9 dB, an OP1dB of -3.4- 0.3 dBm, a PAE of 5.8-13.9% @ OP1dB, and aηof 6.1-14.3% @ OP1dB. 6-10-GHz broadband CMOS TA is measured as a small signal gain of 7.6-10.5 dB, an OP1dB of 2.8-6.1 dBm, a PAE of 8.8-17.6% @ OP1dB, and ηof 9.7-21.1% @ OP1dB.

目錄

第一章 序論  Introduction	1

1  超寬頻(UWB)研究背景與動機	1
2  超寬頻基本原理	1
3  超寬頻頻帶配置	3
4  DS-CDMA超寬頻系統鏈路計算	4
5  論文架構	8

第二章 寬頻輸入、輸出匹配電路及電路線性度之探討	10

1  輸入匹配網路/電路之探討	10
1.1  濾波器型式匹配網路	10
1.2  主動匹配電路	11
2  輸出匹配網路/電路之探討	13
2.1   、 與S11、S22	14
2.2  源極隨耦器	15
2.3  低Q值電感性負載之共源極緩衝器	18
2.4  電阻性負載之共源極緩衝器	23
3  電路線性度之探討	24
3.1  不同型態偏壓元件之電壓及電流擺幅比較	25
3.2  討論	28

第三章 寬頻CMOS低雜訊放大器 (TSMC 0.18 μm)	29

1  低雜訊放大器(LNA)之簡介	29
2  3-5-GHz寬頻CMOS低雜訊放大器	30
2.1  電路架構考量	30
2.2  源極退化電感選擇	30
2.3  放大電晶體最佳寬度選擇	34
2.4  輸出阻抗匹配考量	36
2.5  寬頻放大器之分析	36
2.6  輸入阻抗匹配之分析	38
2.7  完整電路設計考量	40
2.8  模擬與量測結果	41
2.9  結果討論	44
3  6-10-GHz寬頻CMOS單級疊接式低雜訊放大器	44
3.1  電路架構考量	44
3.2  源極退化電感選擇	45
3.3  放大電晶體最佳寬度選擇	45
3.4  疊接電晶體適當寬度選擇	46
3.5  輸入匹配網路設計	50
3.6  考量輸出匹配網路之輸出阻抗分析	52
3.7  疊接放大器等效轉導分析	53
3.8  穩定電路及增益平坦化考量	55
3.9  輸出匹配網路設計	60
3.10  完整電路設計與考量	61
3.11  模擬與量測結果	62
3.12  結果討論	64
4  6-10-GHz寬頻CMOS低雜訊放大器	65
4.1  並聯L-C諧振之探討	65
4.2  寬頻電路架構實現	68
4.3  串接雜訊因數	69
4.4  第一級電路等效雜訊指數相關分析	72
4.5  第二級電路等效雜訊指數相關分析	73
4.6  第三級電路等效雜訊指數相關分析	79
4.7  電路級間寄生電容對雜訊指數影響之分析	81
4.8  完整電路設計與考量	82
4.9  模擬與量測結果	84
4.10  結果與討論	86

第四章 寬頻CMOS折疊式混波器 (TSMC 0.18 μm)	87

1  混波器原理與設計相關考量	87
2  混波器架構探討	89
3  3-5-GHz寬頻CMOS折疊式混波器	91
3.1  3-5-GHz寬頻混波器架構之實現	91
3.2  RF、LO及IF port 三端型態考量	92
3.3  RF端balun設計及阻抗匹配考量	93
3.4  Load1及M1、M2寬度之選擇與考量	96
3.5  切換開關之動作原理	97
3.6  切換開關顫抖雜訊之影響	97
3.7  LO端阻抗匹配之考量	99
3.8  Load2與輸出緩衝器之選擇與考量	101
3.9  轉換增益之分析	102
3.10  模擬與量測結果	104
3.11  結果討論	107
4  6-10-GHz寬頻CMOS折疊式電流鏡混波器	108
4.1  寬頻化電路操作頻寬	109
4.2  輸出端balun分析	112
4.3  模擬與量測結果	114
4.4  結果討論	117

第五章 寬頻CMOS發射放大器 (UMC 0.18 μm)	118

1  發射放大器之相關特性參數	118
2  發射放大器之電路架構考量	119
2.1  高輸出功率之功率放大器相關討論	119
2.2  應用於DS-UWB之發射放大器相關考量	120
2.3  PA及TA之差異	120
2.4  發射放大器電路架構考量	121
3  3-5-GHz寬頻CMOS中間級電感補償式發射放大器	122
3.1  小訊號放大器設計相關考量	122
3.2  驅動放大器設計相關考量	122
3.3  中間級電感補償式網路設計考量	123
3.4  輸出匹配網路設計	123
3.5  模擬與量測結果	125
3.6  結果討論	127_Toc144450232
4  6-10-GHz寬頻CMOS中間級阻抗轉換式發射放大器	127
4.1  小訊號放大器之設計	127
4.2  驅動放大器之設計	128
4.3  中間級阻抗轉換網路之設計	129
4.4  輸出阻抗匹配網路之設計	137
4.5  小訊號放大器增益及Zintr之回顧	141
4.6  完整電路之設計與相關考量	143
4.7  模擬與量測結果	143
4.8  結果討論	146

第六章 結論	147

參考文獻	149

附錄A 疊接放大器之輸入阻抗分析 (考量閘汲極寄生電容)	152

附錄B 疊接放大器之閘-源極壓降分析(考量閘汲極寄生電容)	155
  
                                    

[1] http://www.uwbforum.org/
[2] S. Roy, J. R. Foerster, V. S. Somayazulu, and D. G. Leeper, “Ultrawideband radio design: the promise of high-speed, short-range wireless connectivity,” Proc. IEEE, vol. 92, no. 2, pp. 295-311, Feb. 2004.
[3] www.eurasip.org/content/Eusipco/IST05/papers/426.pdf
[4] S. Jose, “Design of RF CMOS power amplifier for UWB applications,” Thesis for Master of Science, Department of Electrical Engineering, Virginia Polytechnic Institute and State University, 2004.
[5] K. Siwiak, and D. McKeown, “UWB Radio Technology,” UK:Wiley, 2004.
[6] http://www.ieee802.org/15/pub/TG3a.html
[7] A. Ismail, and A. A. Abidi, “A 3.1- to 8.2-GHz Zero-IF Receiver and Direct Frequency Synthesizer in 0.18-μm SiGe BiCMOS for Mode-2 MB-OFDM UWB Communication,” IEEE J. Solid-State Circuits, vol. 40, no. 12, pp. 2573-2582, Dec. 2005.
[8] B. Sklar, Digital Communications : Fundamentals and Applications, Prentice Hall, 2001.
[9] A. Ismail, and A. A. Abidi, “A 3-10-GHz low-noise amplifier with wideband LC-ladder matching network,” IEEE J. Solid-State Circuits, vol. 39, no. 12, pp. 2269-2277, Dec. 2004.
[10] A. Bevilacqua, and A. M. Niknejad, “An ultrawideband CMOS low-noise amplifier for 3.1-10.6-GHz wireless receivers,” IEEE J. Solid-State Circuits, vol. 39, no. 12, pp. 2259-2268, Dec. 2004.
[11] X. Fan, E. Sanchez-Sinencio, and J. Silva-Martinez, ”A 3GHz-10GHz common gate ultrawideband low noise amplifier,” in IEEE Midwest Symp. on Circuits and Systems, pp. 631-634, Aug. 2005.
[12] H. -J. Lee, D. S. Ha, and S.S. Choi, ”A systematic approach to CMOS low noise amplifier design for ultrawideband applications,” in IEEE Int. Symp. on Circuits and Systems, vol. 4, pp. 3962-3965, May 2005.
[13] B, Razavi, T. Aytur, C. Lam, F. -R. Yang, K. -Y. Li, R. -H. Yan, H. -C. Kang, C. -C. Hsu, amd C. -C. Lee, “A UWB CMOS transceiver,” IEEE J. Solid-State Circuits, vol. 40, no. 12, pp. 2555-2562, Dec. 2005.
[14] S. Vishwakarma, S. Jung, and Y. Joo, “Ultra wideband CMOS low noise amplifier with active input matching,” in IEEE Workshop on Ultra Wideband Systems, pp. 415-419, May 2004.

[15] P. P. Ghosh, and E. Xiao, “Design of a new CMOS low noise amplifier for ultra wide-band wireless receiver in 0.18um technology,” in IEEE Int. Conf. on Ultra-Wideband, pp. 514-519, Sep. 2005.
[16] M. Liu, J. Craninckx, N. M. Iyer, M. Kuijk, and A. Barel, “A 6.5-kV ESD protected 3-5-GHz ultra-wideband BiCMOS low noise amplifier using interstage gain roll-off compensation,” in IEEE Int. Conf. on Ultra-Wideband, pp. 525-529, Sep. 2005.
[17] C. -W. Kim, M. -S. Kang, P. -T. Anh, H. -T. Kim, and S. -G. Lee, “An ultra-wideband CMOS low noise amplifier for 3-5GHz UWB system,” IEEE J. Solid-State Circuits, vol. 40, no. 2, pp. 544-547, Feb. 2005.
[18] S. Smith, Microelectronic Circuits, Oxford Univ. Press, 1998.
[19] D. A. Neamen, Electronic Circuit Analysis and Design, Richard D. Irwin, 1996.
[20] B. Razavi, RF Microelectronics, Prentice Hall, 1997.
[21] R. Ludwig, and P. Bretchko, RF Circuit Design Theory and Applications, Prentice Hall, 2000.
[22] T. -H. Lee, The Design of CMOS Radio-Frequency Integrated Circuit, Cambridge Univ. Press, 2004.
[23] C. -H. Wu, C. -H. Lee, W. -S. Chen, and S. -I. Liu, “CMOS wideband amplifiers using multiple inductive-series peaking technique,” IEEE J. Solid-State Circuits, vol. 40, no. 2, pp. 548-552, Feb. 2005.
[24] B. Analui, and A. Hajimiri, “Multi-pole bandwidth enhancement technique for transimpedance amplifiers,” ESSCIRC , pp. 303-306, 2002.
[25] B. Razavi, Design of Analog CMOS Integrated Circuits, McGraw-Hill, 2000.
[26] H. Samavati, H. R. Rategh, and T. -H. Lee, “A 5-GHz CMOS wireless LAN receiver front end,” IEEE J. Solid-State Circuits, vol. 35, no. 5, pp. 765-772, May 2000.
[27] L. Besser, and R. Gilmore, Practical RF Circuit Design for Modern Wireless Systems, Artech House, 2003.
[28] I. Bahl, Lumped Elements for RF and Microwave Circuits, Artech House 2003.
[29] P. Sivonen, and A. Parssinen, “Analysis and optimization of packaged inductively degenerated common-source low-noise amplifiers with ESD protection,” IEEE Trans. Microw. Theory Tech., vol. 53, no. 4, pp. 1304-1313, Apr. 2005.
[30] M. -D. Tsai, C. -S. Lin, C. -H. Wang, C. -H. Lien, and H. Wang, “A 0.1-23-GHz SiGe BiCMOS analog multiplier and mixer based on attenuation-compensation technique,” in IEEE Radio Frequency Integrated Circuits Symp., pp. 417-420, 2004.
[31] Y. -H. Lee, S. -H. Lee, J. Lee, D. -S. Park, S. -H. Cheon, B. Shrestha, S. -J. Kim, G. P. Kennedy, and N. -Y. Kim, “Design of an MMIC broadband mixer with high output power using INGaP/GaAs HBT technology,” in IEEE Asia-Pacific Microwave Conf. Prof., 2005.

[32] T. Manku, G. Beck, and E. J. Shin, “A low-voltage design technique for RF integrated circuits,” IEEE Trans. on Circuits and Systems, vol. 45, no. 10, pp. 1408-1413, Oct. 1998.
[33] I. Kwon, and K. Lee, “An integrated low power highly linear 2.4-GHz CMOS receiver front-end based on current amplification and mixing,” IEEE Micro. Wireless Compon. Lett., vol. 15, no. 1, pp. 36-38, Jan. 2005.
[34] G. Giustolisi, G. Palmisano, G. Palumbo, and C. Strano, “A novel 1.5-V CMOS mixer,” in Proc. of the Symp. on VLSI, pp. 113-117, Feb. 1998.
[35] C. F. Campbell, and J. M. Beall, “Design and performance of a highly integrated wideband active downconverter MMIC,” in IEEE Radio Frequency Integrated Circuits (RFIC) Symp., pp. 245-248, May 2001.
[36] S. -H. Lee, H. -C. Bae, S. -Y. Lee, J. Kim, B. -W. Kim, and J. -Y. Kang, “A 1-6 GHz monolithic up-conversion mixer with input/output active baluns using SiGe HBT process,” in IEEE Silicon Monolithic Integrated Circuits in RF Systems Meeting Dig., pp. 17-20, Sept. 2004.
[37] H. Darabi, and A. A. Abidi, “Noise in RF-CMOS mixers: a simple physical model,” IEEE Trans. Solid-State Circuits, vol. 35, no. 1, pp. 15-25, Jan. 2000.
[38] M. T. Terrovitis, and R. G. Meyer, “Noise in current-commutating CMOS mixers,” IEEE J. Solid-State Circuits, vol. 34, no. 6, pp. 772-783, Jun. 1999.
[39] Richard C. -H. Li, Key Issues in RF/RFIC Circuit Design, 2005.
[40] C. B. Sia, B. H. Ong, K. S. Yeo, J. -G. Ma, and M. A. Do, “Accurate and scalable RF interconnect model for silicon-based RFIC applications,” IEEE Trans. Microwave Theory Tech., vol. 53, no. 9, pp. 3035-3044, Sep. 2005.

校內：2007-09-01公開
校外：2008-09-01公開

簡易檢索 / 詳目顯示

相關論文