| 研究生: |
莊雅芳 Chuang, Ya-Fang |
|---|---|
| 論文名稱: |
溫泉可開發量推估及其應用 Estimation on permissive yield of hot spring |
| 指導教授: |
李振誥
Lee, Cheng-Haw |
| 學位類別: |
碩士 Master |
| 系所名稱: |
工學院 - 資源工程學系 Department of Resources Engineering |
| 論文出版年: | 2008 |
| 畢業學年度: | 96 |
| 語文別: | 中文 |
| 論文頁數: | 84 |
| 中文關鍵詞: | 溫泉 、可開發量 、安全出水量 、指數補注公式 |
| 外文關鍵詞: | Index recharge formula, Permissive yield, Safe yield, Hot spring |
| 相關次數: | 點閱:128 下載:5 |
| 分享至: |
| 查詢本校圖書館目錄 查詢臺灣博碩士論文知識加值系統 勘誤回報 |
臺灣位於歐亞大陸板塊與菲律賓海板塊的接縫處,由於受到菲律賓海板塊不斷的碰撞擠壓歐亞大陸板塊,因而造成台灣地質構造特殊且複雜,其溫泉之形成乃主要藉由地底下有充足的熱源、地下水和破碎的地層,且熱水經由岩層中的裂隙與靜水壓力差上升至地表而形成,亦即溫泉的形成須具備三種要素,即水源、熱源與通路。
台灣擁有豐富的溫泉資源,並且近年來國人對於溫泉水療的日漸重視,使得溫泉需求量亦相對提高,但國內長久以來,對於溫泉資源的恣意開發、缺乏有效管理及規劃。因此,為了避免自然環境遭受破壞,並兼顧天然資源的永續利用,溫泉可開發量評估為主要的議題。
本研究藉由探討形成溫泉的三大要素(水源、熱源與通路)為基本概念,建立一簡化之物理模型,並發展出一溫泉可開發量的推估公式,文中將考慮的所須之三個參數,即水源項的地下水補注量與地下水安全出水率,其中地下水補注量乃經由指數補注公式求得;熱源項以溫差比的觀念代入,考慮初始溫度、穩定最低溫度與目標溫度以及通路項則是考慮岩體之破碎程度,進行溫泉可開發量的推估計算。
本研究以四重溪溫泉和烏來溫泉區作為案例分析,利用上述開發量公式及參數之假設條件下,推估兩區域之溫泉可開發量,結果顯示四重溪及烏來溫泉區之溫泉可開發量分別為22.63×104 m3/年 和278.78×104 m3/年,以供後續開發與利用之參考依據。
Taiwan is located at where the Eurasian and Philippine Plates meet; the frequent relative movements of these two plates cause complicated and fractured geological structure. It leads to that there are plenty of hot spring resources in Taiwan. However, the domestic people increasingly use the hot spring resource and the demand for hot spring is relatively high. Therefore, to avoid the damaging of nature and to ensure continuous utilization, the proper planning and management for hot spring resource become an important issue, especially in estimation on permissive yield of hot spring.
To estimate of hot spring permissive yield, three terms (groundwater safe yield, geothermal resource, and fracture pattern) are being considered for building an empirical model in this study. In the first term, groundwater recharge and safe yield are looked as two main parameters, whereas groundwater recharge is calculated from indexical groundwater recharge method. The geothermal term is controlled by the ratio of temperature difference, which is obtained by initial, steady-lowest, and subjected temperature. The fracture pattern term is considered by a rock quality designation (RQD) index which is used to describe fractured degree of rock matrix in this term. There are two cases, the Sz-Chung-Shi and Wu-Lai hot spring areas in this study. Based on our developed procedures and three factors under the empirical model, the results show that the permissive yield of the Sz-Chung-Shi and Wu-Lai hot spring areas are the value at 22.63×104 m3/year and 278.78×104 m3/year respectively.
1.Barnes C.J., Jacobson G., and Smith G.D., “The distributed recharge mechanism in the Australian arid zone”, Soil Sci. Soc. Am. J., 58, pp.31-40, 1994.
2.Bevans, H.E., “Estimating stream-aquifer interactions in coal areas of eastern Kansas by using streamflow records, in Subitzky, Seymour, ed.”, Selected papers in the Hydrologic Sciences. U.S. Geological Survey Water-Supply Paper, 2290, pp.51-64, 1986.
3.Boussinesq, J., “Essa sur latheories des eaux courantes”, Memoires presentes par divers savants a l’Academic des Sciences de l’Institut national de France. Tome XXIII, No. 1, 1877.
4.Deere, D.U., “Technical description of rock cores for engineering purposes”, Rock Mechanics and Engineering Geology, 1(1), pp.17-22, 1964.
5.Deere, D.U., and Deere, D.W., “The rock quality designation (RQD) index in practice.”, Rock Classification Systems for Engineering Purposes: ASTM STP 984, L. Kirkaldie Ed., American Society for Testing and Materials, Philadelphia, pp.91-101, 1988.
6.Dershowitz W.S., and Einstein H.H., “Characterizing rock joint geometry with joint system models”, Rock Mechanics and Rock Engineering, Vol. 21, pp.21-51, 1988.
7.Finch J.W., “Direct groundwater recharge using a simple water-balance model-sensitivity to land surface parameters”, J. Hydrol., 211(4), pp.112-125, 1998.
8.Hochstein, M.P., “Classification and assessment of geothermal resources. In: Dickson, M.H. and Fanelli, M., eds.”, Small Geothermal Resources: A Guide to Development and Utilization, UNITAR, New York, pp.31-57, 1990.
9.Hu, J.C., Angelier, J., and Yu, S.B., “An interpretation of the active deformation of southern Taiwan based on numerical simulation and GPS studies”, Tectonophysics, 274, pp.145-170, 1997.
10.Kirkpatrick, S., “Percolation and conduction”, Rev. Mod. Phys., Vol. 45, No. 4, pp.574-588, 1973.
11.Kulandaiswamy, V. C., and Seetharaman, S., “A note on Barnes’ method of hydrograph separation”, J. Hydrol., Vol. 9, pp.222-229, 1969.
12.Lee, C.H., and Farmer, I.W., “Fluid flow in discontinuous rocks (1st ed.)”, Chapman & Hall, London, 1993.
13.Lee, C.H., Chen, W.P., and Lee, R.H., “Estimation of Groundwater Recharge Using Water Balance Coupled with Base-Flow-Record Estimation and Stable-Base-Flow Analysis”, Environ. Geol., Vol. 51, No.1, pp.73-82, 2006.
14.Linsley, R.K., Jr., Kohler, M.A., and Paulhus, J.L.H., “Hydrology for Engineers (3rd ed.)”, McGraw-Hill, New York, 1982.
15.Lin, N.F., J. Tang and F.X. Han, “Eco-Environmental problems and effective utilization of water resources in the Kashi Plain, western Terim Basin, China”, Hydrogeology Journal, 9(2), 2001.
16.Long, J.C.S., and Witherspoon, P.A., “The relationship of the degree of interconnection to permeability of fracture network”, J. Geophys. Res., 90(B4), pp.3087-3089, 1985.
17.Phillip F.M., “Environmental traces for water movement in desert soils of America Southwest”, Soil Sci. Soc. Am. J., 58, pp.15-24, 1994.
18.Priest, S.D. and Hudson J.A., “Discontinuity spacing in rock”, Int. J. Rock Mech. Min. Sci. & Geomech. Abstr. Vol. 13, pp.135-148, 1976.
19.Rouleau, A., and Gale, J.E., “Statistical characterization of the fracture system in the Stripa Granite, Sweden”, Int. J. Rock Mech. Min. Sci. & Geomech. Abstr., Vol. 22, No. 6, pp.353-367, 1985.
20.Rutledge, A.T., “A new method for calculating a mathematical expression for streamflow recession, in Ritter, W.F., ed., Irrigation and Drainage”, American Society of Civil Engineers, Irrigation and Drainage Division, Honolulu, Hawaii, 1991, Proceedings, pp.337-343, 1991.
21.Rutledge, A.T. and C.C. Daniel III., “Testing an automated method to estimate ground-water recharge from streamflow records”, Ground Water, Vol. 32, No. 2, pp.180-189, 1994.
22.Sen Z., and Eissa E. A., “Volumetric rock quality designation”, J. Geotech. Engng. ASCE 117, pp.1331-1348, 1991.
23.Sen Z., and Eissa E.A., “Rock quality charts for log-normally distributed block sizes”, Int. J. Rock Mech. Min. Sci. & Geomech. Abstr., Vol. 29, No. 1, pp.1-12, 1992.
24.Simmons C.S., and Meyer P.D., “A simplified model for the transient water budget of a shallow unsaturated zone”, Water Resour. Res., 36, pp.2835-2844, 2000.
25.Smyth J.D., E. Bresler, G.W. Gee, and C.T. Kincaid, “Development of an Infiltration Evaluation Methodology for Low-Level Waste Shallow Land Burial Sites”, NUREG/CR-5523, PNL-7356, RW, WL. , 1990.
26.USGS網站, http://pubs.usgs.gov/gip/dynamic/slabs.html , 2008.
27.Viswanathan M.Th., “Recharge characteristic of an unconfined aquifer from the rainfall water table relationship”, J. Hydrol., 70, pp.233-273, 1984.
28.White, D. E., “Characteristics of geothermal resources. In: Kruger, P. and Otte, C.,eds.”, Geothermal Energy, Stanford University Press, Stanford, pp.69-94 , 1973.
29.丁澈士,土壤水份收支法應用於地下水補注推估–屏東平原個案研究,第八屆水利工程研討會論文集,665-672頁,1996。
30.大陸水利電力部水文局,中國水資源評價,1986。
31.工研院能礦所,台灣地熱資源探勘工作報告之三,經濟部聯合礦業研究所,報告第170號,150頁,1978。
32.工業技術研究院能源與資源研究所,礁溪溫泉區地球物理及鑽井探勘報告,宜蘭縣政府,1993。
33.工業技術研究院能源與資源研究所,台灣溫泉水資源之調查及開發利用(3/4),經濟部水資源局,2002。
34.工業技術研究院能源與資源研究所,台灣溫泉水資源之調查及開發利用(4/4),經濟部水資源局委辦計畫成果報告書,2003。
35.日本地熱學會網站,http://www.soc.nii.ac.jp/grsj/intro/seishitsu.html 。
36.內政部營建署,台灣北部區域計劃規劃作業彙編,1989。
37.李和祥,溫泉資源調查分析之研究–以四重溪與中崙溫泉為例,國立成功大學資源工程學系碩士論文,2005。
38.李京霖,陽明山馬槽地區溫泉資源調查分析之研究,國立成功大學資源工程學系碩士論文,2006。
39.李振誥、馬惠達,金崙與和美福隆地區溫泉資源探勘分析與檢討,溫泉資源開發技術與保育管理研討會論文集,157-194頁,2002。
40.李振誥,陳尉平,李如晃,應用基流資料估計法推估台灣地下水補注量,台灣水利季刊,第50卷,第1期,69-80頁,2002。
41.李振誥、許清荃、林俶寬,濁水溪沖積扇多層地下水調配與管理之研究,台灣水利季刊,第48卷,第4期,41-52頁,2000。
42.李振誥,陳尉平,龔文瑞,陳進發,林宏奕,溫泉可開發量及其應用於烏來溫泉區,台灣水利季刊,第56卷,第1期,60-68頁,2008。
43.宋聖榮、劉佳玫,台灣的溫泉,遠足文化出版社,台北縣,2003。
44.林士哲,金崙地區溫泉資源調查分析之研究,國立成功大學資源工程研究所碩士論文,2003。
45.林峰瑋,知本溪流域地下水資源評估研究,國立成功大學資源工程學系碩士論文,2006。
46.徐年盛、郭振泰、朱文生、王曉中、江崇榮、張德鑫、吳呈懋、傅大章、高尉明,放射性廢料設施及其附近地區地下水流及水質傳輸模擬之研究(一),台大土木工程研究所水利組,水利79013,1991。
47.徐義人,應用水文學,國立編譯館, 133-134頁,2003。
48.能邦科技顧問股份有限公司,台灣地區地下水補注量估算,經濟部水資源局,2000。
49.能邦科技顧問股份有限公司,溫泉蘊藏量推估及開發總量管制評估技術研究 (1/2),經濟部水利署,2006。
50.夏龍源、溫紹炳,臺灣西南麓山地區溫泉資源調查與評估初步研究,第一屆資源工程研討會,697-717頁,2004。
51.陳伸賢,台灣水資源永續發展策略,水資源管理2005研討會–水資源永續利用之管理,台中,1-13頁,2005。
52.陳尚、李德滋,以土壤水分當量推算水稻灌溉需水量之研究,農工學報第10卷,第4期,15-40頁,1964。
53.陳昭旭、李振誥,隧道湧水災害之水文地質調查及其防治處理措施,地工技術雜誌,第87期,81-92頁,2001。
54.陳柏淳、費立沅、蕭如瑾、趙彥婷,天然的尚好?臺灣的溫泉與地熱水探討,地質環境與資源研討會–經濟部中央地質調查所施政成果,149-156頁,2007。
55.陳尉平,由河川流量資料與流量歷線推估地下水補注量,國立成功大學資源工程研究所碩士論文,1999。
56.陳尉平,應用河川流量歷線推估台灣地下水補注量,國立成功大學資源工程學系博士論文,2006。
57.陳進發,彰化地區未飽和層水平衡分析之研究,國立成功大學資源工程研究所碩士論文,1998。
58.陳肇夏,台灣溫泉成因與地熱探勘之我見,地質,第1卷,第2期,107-117 頁,1975。
59.陳肇夏,地熱地質與探勘,貞觀出版社,台北市,1981。
60.陸島工程顧問股份有限公司,烏來溫泉多目標觀光發展工程(第五期)-共同管線委託規劃設計與溫泉點井開鑿第一階段第下溫泉探測調查,台北縣烏來風景特定區管理所委辦計畫成果報告書,2003。
61.陸島工程顧問股份有限公司,屏東縣政府九十二年度四重溪溫泉資源探測與調查案,屏東縣政府,2004。
62.陸島工程顧問股份有限公司,屏東縣溫泉區管理計畫,屏東縣政府,2007。
63.張格綸,應用蒸發皿係數推估地區蒸發散量之研究,國立成功大學資源工程學系碩士論文,2007。
64.程楓萍,臺灣溫泉之地球化學探勘,鑛冶,中國鑛冶工程學會會刊,第23卷,第4期,72-83頁,1978。
65.程楓萍,地球化學地溫指標–應用溫泉化學特性推測地下熱液溫度,能源、資源與環境,6-9頁,1995。
66.溫泉法,中華民國92年7月2日總統華總一義字第 09200121190 號令制定,公布全文 32 條;中華民國94年7月1日行政院院臺經字第 0940023288 號令發布。
67.溫泉標準,中華民國94年7月22日經濟部經水字第09404605610號令訂定。
68.溫泉標準修正條文,中華民國97年5月28日經濟部經水字第09704602550令修正。
69.經濟部中央地質調查所,恆春半島地質圖幅,1991。
70.經濟部中央地質調查所,台灣活動斷層分布圖(第二版),2000。
71.經濟部中央地質調查所,台灣地質圖,2000。
72.經濟部中央地質調查所,臺灣溫泉分布圖,2006。
73.經濟部水利署,台灣地下水資源圖﹙地下水流模數,M﹚,2002。
74.經濟部水利署,台灣地下水資源圖(地下水逕流係數, ),2002。
75.經濟部水利署,台灣地下水資源圖(河川基流係數, ),2002。
76.劉佳玫,台灣南部二氧化矽熱流量及熱構造之研究,國立臺灣大學碩
士論文, 2001。
77.劉振宇、李天浩、蘇明道、林國峰,濁水溪沖積扇扇央與扇尾平原區地表垂向補注量評估,經濟部水資源局,1998。
78.劉進金、周順安、曾鈞敏、譚義績,溫泉資源之保育與管理,溫泉資源開發技術與保育管理研討會論文集,145-156頁,2002。
79.劉聰桂,由碳十四定年與氚示蹤探討濁水溪沖積扇地下水的流速與補注,地下水資源及水質保護研討會論文專輯,1-24頁,1994。
80.劉聰桂、宋聖榮,溫泉水質與水量,溫泉資源開發技術與保育管理研討會論文集,69-88頁,2002。
81.劉聰桂、楊燦堯、吳文雄,台灣的岩石,遠足文化出版社,台北縣,2005。